ON AIRTuning in…NEXT …Radio page

How to Use Pixel Art on Flyers, Posters and Business Cards: A Resolution Guide

2026/11/19 · Using images · about 7 min to read · by jeid (Otomusu site owner)

Why Pixel Art Looks Sharp on Screen but Blurry in Print

Have you ever put pixel art on a flyer, business card or poster, only to find it looks fuzzier than it did on your screen?

Most of the time, the cause is a mismatch between the image’s resolution (how much detail it contains) and the size you want to print. Pixel art is naturally tiny, often just 32×32 pixels. When you print it on a large sheet of paper, the wrong enlargement method will smear the outlines or make them jagged.

This article walks through how to think about printing pixel art, using simple calculations and steps. You don’t need any specialized knowledge, just basic arithmetic.

First, Understand “Pixels” and “dpi”

Print detail is usually expressed in dpi (dots per inch). One inch is about 25.4 mm. For ordinary printed materials, around 300 dpi is commonly used as a guideline, and you can use it as a baseline to work out how many pixels you need.

The formula is:

Required pixels = paper length (mm) ÷ 25.4 × 300

Applying it to common paper sizes gives the following (rounded to the nearest whole number):

Paper Size (mm) Pixels needed at 300 dpi
Business card (91×55, the standard Japanese size) 91×55 about 1075×650
A5 148×210 about 1748×2480
A4 210×297 about 2480×3508
A3 297×420 about 3508×4961

In other words, “to fill an A4 page, you need an image roughly 2480 pixels wide.” Since pixel art might be only 32 pixels wide, you can see right away that it can’t be used as is.

The Key Is to Scale by a Whole Number

The most important tip for enlarging pixel art is to scale it by a whole-number multiple (2×, 3×, 10×, and so on) and choose an enlargement method that does not use interpolation.

In many image editors, the default enlargement setting uses “interpolation,” which blends colors smoothly together. That works well for photos, but with pixel art it blurs the edges between the square dots and makes the image look soft. If your software offers options with names like “Nearest Neighbor,” “Nearest Neighbor Interpolation” or “Preserve Hard Edges (Pixels),” choose one of those. The setting name varies between programs, so check your software’s documentation.

Also, an awkward scale factor such as 1.5× or 2.3× makes the dots uneven in size, so lines look thicker in some places and thinner in others. Always use a whole-number multiple.

Enlargement Guide by Original Size

The table below shows what happens when commonly used pixel art sizes are enlarged by whole-number multiples. The print sizes are for 300 dpi.

Original size Scale Enlarged size Print size at 300 dpi (approx.)
16×16 80× 1280×1280 108 mm (about 11 cm)
32×32 40× 1280×1280 108 mm
32×32 60× 1920×1920 163 mm (about 16 cm)
64×64 30× 1920×1920 163 mm
64×64 37× 2368×2368 200 mm (about 20 cm)

For example, suppose you want to place a 32×32 character across the full width of an A4 page. 2480 ÷ 32 = 77.5, so round down to 77× (2464 pixels). Center the image and treat the leftover width as margin. The dots stay a uniform size, and you still use almost the full width.

The Actual Process (6 Steps)

  1. Decide the print size: First decide whether it’s a business card, a flyer or a poster.
  2. Calculate the pixels you need: Using the table above as a reference, calculate from the size (in mm) you want the image to be.
  3. Choose a whole-number scale: Pick the multiplier where original size × scale comes closest to the pixel count you need.
  4. Enlarge without interpolation: In your image editor, switch to a setting such as Nearest Neighbor and enlarge. The free browser-based image tools can also help you prepare by cropping and enlarging.
  5. Tidy the background and margins: Check that no white edges appear and that the image works well against the background.
  6. Export and do a test print: Print once on a small sheet of paper and check the colors and any blurring.

Watch Out for Color Differences, Too

Screens create color with light, while printing creates color with ink. As a result, colors that looked vivid, almost fluorescent, on screen often look duller in print. The difference is said to show up especially with bright blues, vivid greens and pinks.

Here is what you can do about it:

  • Pixel art uses few colors, so color differences stand out. Always do a test print.
  • How colors look also varies between print shops and home printers, so check in the same environment you’ll actually use.
  • Adjusting important colors slightly darker can sometimes bring them closer to what you want after printing.

How much the colors change depends on the paper and the type of printer. It can’t be pinned down with numbers, so checking with a real printout is the surest way.

Common Mistakes

Mistake 1: Stretching a small image in your editing software at the last minute

If you stretch an image with the software’s enlarge button right before printing, interpolation tends to blur it. Create the whole-number-enlarged image first, then place that image in your layout.

Mistake 2: Using a screenshot of the image shown on screen

A screenshot is a small image that depends on your screen size. It almost never has enough resolution for printing. Use the original file instead.

Mistake 3: Placing the image right at the edge and having it cut off

In printing, the edges of the paper can be trimmed slightly. To be safe, keep important parts a few millimeters to about 1 cm inside the edge.

Mistake 4: Dots close to the background color got lost

Pixel art with colors similar to the background has outlines that become hard to see once printed. Make the background a little darker or lighter to create a clear difference.

Pre-Publication Checklist

  • Did you calculate the required pixels from the print size?
  • Did you enlarge by a whole-number multiple using a method without interpolation?
  • Are there any white edges or semi-transparent smudges left around the image?
  • Are any important parts too close to the edge of the paper?
  • Did you do a test print and check the colors and outlines on the real thing?
  • Did you check the terms of use for the asset (whether uses such as flyers, business cards and merchandise are permitted)?

The last item is very important. Depending on the asset, the conditions for distributing printed materials or selling merchandise may differ. If you use Otomusu assets, please check the Terms of Use. If anything is unclear, you can ask through Contact. You can find pixel art assets on the Pixel Art page.

Summary

  • Around 300 dpi is the guideline for print detail. Paper size (mm) ÷ 25.4 × 300 tells you the pixels you need.
  • Enlarge pixel art by a whole-number multiple, without interpolation.
  • Turn leftover width into margin so the dots stay a uniform size.
  • Colors look different on screen and in print, so always do a test print.
  • Check the terms of use for each use you have in mind.

To start, try printing one of your favorite pixel art pieces at business card size. Even a small test will give you a feel for scale factors and color. With that experience, you can work on flyers and posters with confidence.

Terms of use for the assets

  • Free
  • No registration
  • Commercial use OK
  • Edits OK
  • Credit optional
  • No usage report needed

See the terms of use for details.

Related articles

Waiting to play
0:00 / 0:00